Hazard lights are those lights which are indicative of a potential hazard that the vehicle flashing it may pose. When the lights are switched on, the four indicators (front and rear - right and left) begin to blink at the same time. This is an indication to all the vehicles passing it that there may be some problem with it. They are also called warning flashers, warning lights, flashers or 4-way flashers. These lights have to be independent of any other lighting or indication system provided in the car. 

1) Important Air Conditioner Terms

SEER: Seasonal Energy Efficiency Ratio. Just remember this, higher the SEER, more will be the efficiency of unit, resulting in a lower operating cost.

Blower (Blower Motor): The motor and fan assembly mounted near the evaporator that draws air over the evaporator. In automotive applications, the blower motor may draw outside or inside air, depending on control settings.

Charging: Adding refrigerant to a system.

Adaptive Headlight System :-

Suppose you are driving home from a weekend vacation. It's late at night, and the winding two-lane road has no streetlights. You approach a curve at 40 mph -- slow enough to make the turn, but too fast to stop suddenly if you need to. 
In this case what would you do ?
 

Transportation of fluids uses different types of tubes, among which most commonly used tubes are hoses and pipes. They are efficient in transferring liquids from one point to the other.We will discuss the difference between hose and pipe in this article.

Elon Musk ha rivelato un piano per alleviare la congestione della città che vedrebbe una rete sotterranea di tunnel che trasportano auto su pattini ad alta velocità che viaggiano a 130 miglia orarie.

L'imprenditore e fondatore di Tesla ha presentato la sua visione per The Boring Company insieme a un video durante un TED Talk la scorsa settimana a Vancouver. Ha fondato l'azienda alla fine del 2016 dopo essere diventato frustrato dalla rete di trasporti di Los Angeles.

Fabrication and manufacturing are industrial terms linked to the process of production or construction. Often, the two processes are confused, yet they are very different from each other. In this article we will explore the meaning of both fabrication and manufacturing in industrial processes.

In Mechanical Engineering,drawings are made either in first angle projection or in third angle projection.We do not make drawings in second or fourth angle projection.We will discuss the reason behind doing so in this article..
Let us first understand the concept behind the angle projection system. Imagine you have Vertical Plane (VP) and Horizontal Plane (HP) (Perpendicular to each other),now we have 4 quadrants. For 1st angle projection system, we place object in 1st quadrant, for 2nd angle projection system, we place object in 2nd quadrant and so on.

You all must have seen the hole in the washbasin. Have you ever wondered, what is the purpose of these holes on the side of a sink. We will discuss the purpose of the hole in the washbasin in this article.

This opening is located on the wall of the basis nearest to you, near the top of the basin. The overflow opening serves two important functions:

1.)If the water tap is left on while the drain stopper is closed, the opening will channel water down into the drain opening rather than letting is spill out of the sink onto the floor.

You might have wondered why 100cc scooter gives less mileage than 100cc manual transmission bike. Think about it where a 100cc scooter returns mileage near 40-50 Kmpl, an average 100cc motorcycle provides mileage over 60 Kmpl. The answer to this question lies in the transmission used where the scooters use automatic CVT transmission, while motorcycles use a proper 4 or 5 speed manual transmission.We will discuss about the reason behind this in this article.

Let us first understand the concept behind the angle projection system. Imagine you have Vertical Plane (VP) and Horizontal Plane (HP) (Perpendicular to each other),now we have 4 quadrants. For 1st angle projection system, we place object in 1st quadrant, for 2nd angle projection system, we place object in 2nd quadrant and so on.